It’s important that you haven’t started working under your sports car and find the answer to how you jack up C5, C6, C7, and C8 Corvettes. Many people get on the repairing job and end up in an accident.
Today, in this article, we’ll reveal much more than how this car lifts. So, let’s get to the details below.
Take Safety Precautions
Whether you have your insurance or not, your life is precious. Never compromise on your safety, and make sure you have taken safety precautions while working under the car.
When it comes to the C5, C6, C7, and C8 Corvettes keep in mind that the floor jack is your finest option. But not an ordinary floor jack will get this job done. Since all the mentioned Corvettes weigh approximately 3500 pounds or less, opt for a floor jack that easily lifts them.
Find some jack stands as well when you buy a floor jack. Don’t get under your vehicles until the stands support the weight.
Where to Jack up a C5, C6, C7, and C8 Corvettes?
One ignorance folks out there do about the ground. When you are lifting your Corvette, it’s necessary to place it on even ground. Soft ground will let the jack and jack stand sink in, and apparently, this will cause an accident.
Bring your sports car on the hard flooring. Asphalt and concrete grounds are ideal in that regard. As these floors are well-built, they prevent slipping. It allows you to focus on the repair job and perform it real quick.
Even on these grounds, it’s important that your car is straight and not tilted from one side due to one reason or another. So, before you get into going, pay attention to it. Initiate working by engaging the handbrake and shifting the car to first gear or neutral.
How to Chock the Wheels of the Corvette?
Now, when you are all set with the brakes engaging and bringing your car to hard ground, the next step is chocking. No matter if it’s your C5, C6, C7, or C8 Corvette, chocking is necessary.
You need to put the blocks to prevent the movement of your vehicle. These blocks seize your car in the specific position it is in and allow for safe lifting with the jack.
Note that if you lift your sports car in the garage and it’s inclined, you need to be more careful. However, the right placement of the blocks is the key. Follow the “Opposite Tire” rule here.
Whenever raising the front tire of the Corvette, make sure the chocks are placed behind the rear wheels. In the case of rear wheels, the chocks will be positioned before the front wheels.
In an instance, if you need to lift the front left tire, put the chocks on the rear right tire and vice versa. This way, the lifted car will stand tall.
Where are the Jack Points under the C5, C6, C7, and C8 Corvettes?
You don’t jack up your car from anywhere. There are jack points manufacturers have already installed for lifting your car. Through these points, the saddle of your floor jack comes into contact and raises your car.
On C5, C6, C7, and C8 Corvettes, you’ll find these jack points on the frame under your car. Two of the jack points are located behind the front two wheels. Or, you can say they are under the front driver and passenger seat.
For lifting the car from the rear sides, you’d need to place the jack at the back. Two jack points are integrated on the backside. They come before the back wheels.
Make sure you lift your expensive car using these points.
How to Place a Jack under the Vehicle?
Prior to buying the floor jack for your car, check out the minimum and maximum lift height. As for the Corvette, the C5 has a ground clearance of 3-3.5 inches; the C6 has 3.7 inches, the C7 has 4 inches, while 5.3 inches is the clearance of the C8.
Buy a floor jack keeping in view the minimum lift height. When done buying one, it’ll be really easy for you to get the jack under. Bring your jack near your car and slide it under the seat doors. Since it’ll have the height-compatible model for your car, it fits well.
How to Raise the Corvette?
Get your low-profile jack under after finding the jack points for your Corvettes. The next step to this is to start pumping. Know here that there’ll be a distance between the jack point and your jack at first.
When you keep pumping the jack, the saddle of your floor jack will reach the jack point. Secure the grip of your jack on the jack point. Once you are sure of the grip, start pumping again.
With this pumping job, you’ll lift your car. However, you need to be certain of the maintenance job your car requires. Keeping in view the type of maintenance, you can target the height of the jack and, ultimately, your car.
Where to Place a Jack Stand under the C5, C6, C7, and C8 Corvettes?
On the chassis of the C5, C6, C7, and C8 Corvettes, there is a beam adaptor. When you are done placing your jack and jacking up with it, place the jack stands under the beam adaptors. The jack points are the same for floor jacks and jack stands, which can be found in the manual as well.
You can also put your stands toward the rear wheels. There are frame contact locations that are suitable for placing the jack stands. With the jack stands, you also need to make sure to raise them to the maximum height desired.
How to Lower the Corvettes?
Restoring your car to the ground after you are done with maintenance and repair is a crucial task. If your car lowers quickly, there’s a higher possibility of its parts getting damaged.
Whenever dropping Corvette, make sure the process is slow and smooth. First, place the jack under your car, and lift it a few inches higher than your jack stands. Remove the jack stands once the jack has lifted the car higher.
Next is to open the release valve of your floor jack. Opening this valve, bring back your car to the ground level.
How to jack up C5, C6, C7, and C8 Corvette? Above, we told you to use the jack stands and floor jack for the purpose. All you need to do is find the jack point under your sports car, place the jack, and pump it.
During this process, make sure you take safety precautions in terms of using jack stands and buying the right floor jack for your needs. Stay safe, and stay keeping your car up to date.
You May Also Like: How to Jack up a Golf Cart For Changing a Tire