Jacking up a Mazda is just a few steps process, provided you have the right location and tools available. Whether it’s a Mazda CX5, 2, 3, 6, CX9, CX6, or MX5, they all follow the same jacking process, though the capacity of the tools may vary.
Since you have made it this far, you don’t need to worry about any of this, as we will guide you through the process for each Mazda model and the appropriate jack required.
Let’s dive into the article.
Tools Required for Jacking up the Mazda
You will need a floor jack, jack stands, and wheel chocks. These basic tools will help you get the job done. The floor jack will lift your car, and the stands will be placed afterwards to hold the load for an extended period. The chocks prevent the wheels from moving since the car will be lifted, reducing the risk of slight sliding.
Since chocks are universal, you can use any of them for any Mazda model. However, it’s essential to double-check the floor jack and stands to ensure they can support the load. The general rule is that if you have tools with a higher capacity than your Mazda’s weight, you can use them for your car.
For Mazda models CX5, 2, 3, 6, CX9, CX6, and MX5, a 3-ton jack will work for all of them. As all of the mentioned models weigh less than 3 tons (6000 lbs), they can be easily jacked up with the jack. The capacity of the jack stands should follow that of the jack.
Related: Discover the Best Floor Jack for Miata: Your Ultimate Guide
Below is the list of Mazda models and the recommended capacity of the jack that will work for each of them.
| Mazda Model | Weight (lbs) | Recommended Jack (tons) |
| Mazda CX5 | 3500 – 4000 | 2 – 2.5 |
| Mazda CX9 | ~ 4400 | 2.5 – 3 |
| Mazda MX5 | ~ 2000 | 1.5 – 2 |
| Mazda CX6 | ~ 3500 | 2 – 2.5 |
| Mazda 2 | 2000 – 2500 | 1.5 – 2 |
| Mazda 3 | ~ 3000 | 2 – 2.5 |
| Mazda 6 | ~ 3500 | 2 – 2.5 |
Preferred Location for the Lifting
You should lift your car on a hard and even ground to reduce the chances of sinking or sliding. Your garage would be a preferred spot for this task. However, if you have a driveway that meets the criteria, it can be suitable as well.
Jacking up on the road is also feasible, but you should ensure there is no traffic around. If you experience a flat tire in the middle of the road, that’s a different case. However, if you are planning to perform maintenance, you should avoid doing so on busy roads with traffic.
Even if you are using chocks and the handbrake is engaged, you should still avoid inclined surfaces for safety purposes.
Which Wheels Should You Chock
Always chock the wheels that stay on the ground, not necessarily all of them. If you are lifting the front, chock the rear wheels. The chock should be placed at the back of the rear tires. Do the opposite for raising the back tires.
Another method is the diagonal approach. For raising the right front wheel, chock the rear left wheel. This diagonal method is applicable to all the wheels.
However, if you don’t have chocks and you’re lifting one tire just to replace it with a new one, it’s still acceptable, but be cautious not to raise the car too high. Lifting the tire an inch or two will provide enough space to remove it without the car being too high off the ground, reducing the risk of sliding.
Jacking Points in Your Mazda
The factory jack points can be found in the manual as they may vary depending on the model. However, in most cases, the lifting points are located near each wheel, underneath the doors. Upon inspection, you should be able to identify the marked areas for jacking.
It is crucial to avoid using fragile parts as lifting points. If you choose weak or easy-to-break points, the jack could penetrate the car, causing it to come down rapidly and posing a safety hazard. Always use solid points that are specifically labeled for the model to ensure safe and proper lifting.
How to Raise the Mazda CX5, Mazda 2, Mazda 3, Mazda 6, Mazda CX9, Mazda CX6, and Mazda MX5.
Once you have found the jack point, position the jack underneath it. Pump the jack to raise the car, providing enough space to install the stands. Before lifting the car, determine how high you need to lift it to accommodate the stands.
The height of the stands is adjustable, so the car should be raised an inch or two higher than the stand’s height. Now, where should you place the stands?
If you want to raise the front right tire, jack up the rear right tire to create enough space for the jack stand to be installed at the front right tire’s jack point. Repeat the same process for the opposite tires and sides.
Once the stand is in place, lower the floor jack, and the car will come down and rest on the stand. This method is useful when you can’t raise and install the stand at the same or near the same point due to limited room.
Lowering the Mazda
Lowering is quite easy once you have successfully jacked up the car. Return to the same jack point you used before. This time, lift the car higher than the stand’s height so that the load stays on the floor jack, not on the jack stand.
Once that’s done, remove the stand, and slowly rotate the jack’s handle to lower the car gradually.
Ending Notes
This is how to jack up Mazda CX5, Mazda 2, Mazda 3, Mazda 6, Mazda CX9, Mazda CX6, and Mazda MX5. Make sure you have the right tools available and that the parking spot is solid enough so that the car or jack does not penetrate into the ground. Follow the above method carefully to safely lift your Mazda.
If you are still unsure about how to jack it up, you should consult a professional or have a companion who can assist you.
You May Also Like: The 3 Best Jack Stands for BMW